BRUSH LESS MOTOR DRILLING AND MILLING MACHINE BF30VB

• Extremely Reliable, Brushless DC Variable Speed Motor Included Standard
• Belt Drive Design, For Smoother, Quieter Running
• Extra Large Column To Base Mount
• 3 Bolt Head to Column Mount is Standard, Also For Increased Rigidity
• Larger Dials at Table Ends, Graduated in .001", For Easier Reading,  And More Accurate Table Movements
• Leadscrews Are True Inch Pitch Screws (Not Metric Conversions Like Many), 10 Threads Per Inch (.100" Per Turn)
• Machine Carries A 3 Year Warranty For Added Peace Of Mind
• More Information below under the DESCRIPTION Tab below - It is NOT just the same old model with just a belt drive upgrade

• MUCH Larger Travels and work area
• Quill DRO Included Standard (This is for the spindle up/down movement) 
• 3 Bolt Head Mount is now standard (where the head mounts to the Z Axis), for more rigidity when milling - Much improved over the single bolt mount type
• Main Z Axis Column is attached to the base with 4 bolts, and mounted from the top, with a wide, proper mounting surface for much more rigidity over other models in this size range
• .001″ Readings with larger dials on the X and Y axis, with true 10 Thread Per Inch Leadscrews make it easier to cut accurately - (One line on the dial is .001″, one full turn of the handwheel is .100″, much easier to use than those with odd metric conversions)
• 50-3000 RPM variable speed with the turn of a knob, properly set up with Low and High for a wider speed range, and plenty of power at lower speeds
• Precision ground ways for smoother movements - Not just rough milled
• Thrust Bearings in leadscrew ends - not bushings - Much smoother movements and less backlash
• Split nuts on X and Y Axis to allow for backlash adjustment
• DC BRUSHLESS MOTOR, Variable Speed, POWERFUL, SMOOTH, and RELIABLE Belt Drive from Motor to Spindle runs MUCH quieter than others, and eliminates any failure prone plastic gears (And the hassle of changing them when stripped)

Main Specifications INCH system 

Model BF30VB (DC Brushless Motor,and Belt Drive Head is Standard)
Max. Drilling Capacity 1-1/4″
Max. End Milling Capacity 3/4″
Max. Face Milling Capacity 3-1/2″
Table Size 8-1/4″ x 33″
Cross Travel (Y Axis) 8-3/4″
Longitudinal Travel (X Axis) 23″
Table Leadscrew Pitch 10 TPI (.100″ Per Turn)
Table Dial Graduations .001″
Vertical Travel (Z Axis) 14″
Max Distance Spindle to Table 17″
Taper of Spindle R-8, w/7/16-20 Drawbar Thread
Spindle Travel 3″
T Slot Size Actual size 14mm, our 9/16″ kit listed is sized for this machine
Range of Spindle Speeds 50-3000 rpm, 2 Ranges (Properly set up with high and low range belt positions for more power at lower speeds as it should be)
Headstock Tilt Left & Right ±90°
Motor 2 HP
Net Weight (Not Including Base) 530 LBS
Net Weight (With Base) 605 LBS
Power Required 220V, Single Phase, 10 Amp

Dimensions
Optional Stand Height 28″
Table Surface Height (On Stand) 36″
Height, Head at normal working height (W/O Stand) 39"
Max Height, Head at top of travel (W/O stand) 48"
Height, Head at normal working height (On Stand) 67"
Max Height, Head at top of travel (On stand) 76"
Width, Tip to Tip of table handles 46-1/4"
Dimension Front To Back, from back of chip pan, to front table handle tip 31"

.Our machine  WMD30V specification